Lot codes for Corsair products can generally be found in the follow locations. For more specific information, please view the Corsair knowledge base Lot Code article for a particular product series.
Headsets: The code is located on the earcup's arm.
Speakers: The code is located on the back of the subwoofer.
Case: The code is located on the back panel.
Cooling: The code is located on the radiator.
Flash: The code is located on the unit's packaging, near UPC barcode.
SSD: The code is located on the label on top of the SSD.
Mice: The code is located on the label taped next to the USB connector.
Keyboard: The code is located on the packaging near the UPC barcode.
Memory: The code is on the memory module's label.
PSU: The code is on the PSU label, next to the serial number.
Our Graphite Series? 600T mid-tower case is equipped with an easily accessable fan controller on the exterior of the case. This short guide will show you how to properly connect this fan controller to the fans in your new case.
Locating the Fan Controller Cables
The fan controller knob is on the top of the case, and is pictured below. This knob controls the speed of the fans connected to the fan controller. Turning the knob to the left lowers the fan speed, while turning the knob to the right raises the speed.
Remove the side panel from the 600T behind the motherboard tray. The fan controller cables are strapped to the case, as shown below. Release the cables by cutting the zip tie.
Understanding Each Cable
- There are a total of six cables shown below
- Cables highlighted in red are the power fan connector cables, which are used to connect up to four fans
- The cable highlighted in green connects to a 4-pin Molex cable from your power supply, providing power to the fan controller knob and the four fan connector cables
- The cable highlighted in yellow is the top 200mm fan connector
- The other 200mm fan cable can be located backside bottom left of the case (not shown in picture below)
Using the Fan Controller
To connect a fan to the fan controller, the protective cap must first be removed. Removing the cap is simple, grab a hold of the cap (enclosed in red) and pull down from the fan power connector (enclosed in yellow). The cap will easily slide off.
Once the cap is removed, two pins are revealed, allowing you to connect the two 200mm case fans.
Locate the two 200mm case fans power cables on the back of the case. When located, plug the 2-pin fan controller cable to each 200mm case fan.
Once the 2-pin fan controller power cables are connected to the 200mm case fans, installation is complete.
Note that you still have two additional 2-pin fan controller power cables if you desire to add more case fans.
Turn the system on and enjoy!
How do I make a warranty claim?
Prior to submitting your warranty claim, we recommend checking the Corsair knowledge base at http://corsair.com first, where you can find answers to commonly-asked questions. You can also receive troubleshooting assistance by clicking Ask a Question or proceed with product replacement by clicking Request an RMA.
Valid warranty claims should be processed through the retailer where the item was purchased during the first thirty (30) days after purchase. This period may vary depending on where you purchased your product; please verify the return policy with the retailer where you purchased your product. Any warranty claims that cannot be processed through your original point our purchased should be submitted to Corsair at http://corsair.com.
What are Corsair's replacement options?
Corsair offers the following Warranty fulfillment options:
Through Corsair's Standard Replacement process, Corsair will issue an approved RMA number for the return and replacement of your defective product(s). Our Standard Replacement processing time from receipt of your product(s) to the replacement product(s) shipment is 1-3 business days plus transit time.
At Corsair, we understand the need to be up and running at all times! To minimize down time, we offer an Express Replacement RMA process. Through this process Corsair will ship your replacement product(s) prior to receiving your defective product(s). This process requires a valid Credit Card where a holding fee will be applied for the cost of the product until the returning product(s) are received by Corsair. To avoid being fully charged for the Express Replacement product(s), the defective product(s) must be received by Corsair within 10 business days from the date your Express Replacement order is shipped.
Accessory Product Request:
Experiencing a problem with a Corsair Component Product? Many of Corsair products have easy to install replacement accessories which will resolve the issue and prevent the need to return the entire product for replacement.
Where do I ship my items?
Corsair operates multiple RMA receiving locations worldwide. Your RMA confirmation will specify the specific return address you must use when sending your RMA package. This will be your standard return location and should not be changed without prior approval from Corsair. Any packages received at an unauthorized location may be refused and returned to the sender at the sender's expense.
1) WATCH: How do I use the fan controller on the 600T case?
The Carbide Series cases come with both USB 3.0 and USB 2.0 support. If your motherboard does not have a USB 3.0 header, then you can use the supplied 3.0 to 2.0 USB adapter which comes with the case. Check out the video below showing you how it?s done: Link2) How many fans can be controlled by the integrated fan controller on the 650D?
The fan controller can control up to 4 different fans in your system.3) Will my graphics card fit in the 650D?
This case will fit any graphics card currently on the market, and even if larger cards are released in the future, our HDD cage is removable and can be relocated to the bottom of the case if you require more space.4) Does the 650D support USB 3.0?
Yes! The 650D has a front USB 3.0 port which will support your USB 3.0 devices.5) What size motherboards will the 650D support?
The 650D will support ATX and mATX motherboard form factors.6) Do the HDD cradles in the 650D support SSDs and other 2.5in form factor drives?
Yes, the hard drive cradles in the 650D are able to secure a 2.5in HDD, SSD or any standard 3.5in drive.7) How many fans come with the 650D?
The 650D comes with 2x 200mm fans and 1x 120mm fan.8) Can I fit 3x graphics cards in the 650D?
The 650D has 8 expansion slots and we have test fit our 650D with triple video card configurations without any problems. You should have plenty of room for this configuration.9) WATCH: How do I connect the USB 3.0 front panel connector on the Carbide Series cases to my motherboard?
The Carbide Series cases come with both USB 3.0 and USB 2.0 support. If your motherboard does not have a USB 3.0 header, then you can use the supplied 3.0 to 2.0 USB adapter which comes with the case. Check out the video below showing you how it?s done: Link10) Will the Carbide Series cases support an internal 240mm radiator?
Yes! The Carbide Series cases are designed to accommodate 240mm radiators.11) Will the Carbide (400R/500R) Series cases support 3-way SLI/Crossfire?
The Carbide Series cases have 8 PCI expansion slots, which will allow the support of 3-way SLI/Crossfire.12) How many fans come with the Carbide Series 400R? How many fans will it support?
The Carbide Series 400R comes with 3x 120mm fans. There are a total of 10 fan mounting points in the case. 6 of these mounting points will accept either 120mm or 140mm fans, and the remaining 4 will only accept 120mm fans.13) Will my graphics card fit in the Carbide Series cases?
The Carbide Series cases have 316mm of space for graphics cards, which should be enough for just about any card!14) How many fans can be controlled by the integrated fan controller on the 600T?
The fan controller can control up to 4 different fans in your system. For more information about the configuration and features of the fan controller please check out this blog post
.15) Can I fit 3x graphics cards in the 600T?
The 600T has 8 expansion slots and we have test fit our 600T with triple video card configurations without any problems. You should have plenty of room for this configuration.16) Will my graphics card fit in the 600T?
This case will fit any graphics card currently on the market, and even if larger cards are released in the future, our HDD cage is removable and can be relocated to the bottom of the case if you require more space.17) Are there any alternative side panels or accessories for the 600T?
Alternative side panels and accessories for the 600T can be purchased separately in the case accessories section
of our website.18) Does the 600T support USB 3.0?
Yes! The 600T has a front USB 3.0 port which will support your USB 3.0 devices.19) What size motherboards will the 600T support?
The 600T will support ATX and mATX motherboard form factors.20) Do the HDD cradles in the 600T support SSDs and other 2.5in form factor drives?
Yes, the hard drive cradles in the 600T are able to secure a 2.5in HDD, SSD or any standard 3.5in drive.21) What size radiator will fit in the top of the 600T?
The case is designed to accommodate most a 2x 120mm (240mm) radiator at the top of the case. In order to use a radiator you will need to remove the 200mm fan at the top of the case.22) What are the specifications for the 200mm fans included in the 600T?
RPM = 800
CFM Max = 76
dBA Max = 2423) How many fans come with the 600T?
The 600T comes with 2x 200mm fans with white LED lights and 1x 120mm fan.24) Do the hot swappable HDD cradles in the 800D support SSDs and other 2.5in form factor drives?
Yes, using the screw holes on the bottom of the cradle (rather than the sides, which are used for standard 3.5in drives) you can secure a 2.5in HDD or SSD.25) A part on my case has been damaged; do I need to have my whole case replaced?
In most instances you do not need to have the whole case replaced, we can replace the damaged part individually. Please use Corsair Customer Portal
to submit a request.26) If I decide to mount fans on the top of the 800D, should they be used for exhaust or intake?
In most systems we would suspect that exhaust fans would make the most sense to be mounted on the top of the case. Every system is going to be slightly different so there is definitely some room to experiment.27) Can I order a non-windowed side panel for the 800D?
Absolutely! Please check the corsair store, here: Link28) Does the 800D support USB 3.0?
Newly purchased 800D already support USB 3.0. If you have an older 800D then you can purchase an upgrade kit by going to this Link29) What size motherboards will the 800D support?
They will support mATX, ATX, eATX.30) What size radiator will fit in the top of the 800D?
The cases are designed to accommodate most 3x 120mm (360mm) radiators with enough space to support push/pull configurations. Measured from edge to edge of the mounting holes on the top of the case there is 10 mm of space between mounting holes.31) I would like to use a 120mm fan on the rear fan mounting area or the 800D, is that possible?
The rear fan mounting location will support either a 140mm OR 120mm fan.32) What are the specifications for the 140mm fans included in the 800D?
RPM = 900 +-150
CFM Max = 69
dBA Max = 17.933) How many fans come with the 800D?
The 800D comes with 3x 140mm fans, and the case will support and additional 4x 120mm fans.34) How do I remove the 5 1/4 plastic drive bay covers on the 800D?
The aluminum face plate on the front of the case is removable and it will need to be removed before you have access to remove the drive bay covers. You will want to hold the top of the case with one hand and then pull outward from the bottom of the face plate. The aluminum face plate should come right off and once you remove the necessary drive bay covers you can simply line up the face plate and snap it back into place.