Support

The Carbide Series cases come with both USB 3.0 and USB 2.0 support.  If your motherboard does not have a USB 3.0 header, then you can use the supplied 3.0 to 2.0 USB adapter which comes with the case. Check out the video below showing you how its done:

The fan controller can control up to 4 different fans in your system.

This case will fit any graphics card currently on the market, and even if larger cards are released in the future, our HDD cage is removable and can be relocated to the bottom of the case if you require more space.

The 650D will support ATX and mATX motherboard form factors.

Yes, the hard drive cradles in the 650D are able to secure a 2.5in HDD, SSD or any standard 3.5in drive.

The 650D comes with 2x 200mm fans and 1x 120mm fan.

The 650D has 8 expansion slots and we have test fit our 650D with triple video card configurations without any problems.  You should have plenty of room for this configuration.

Yes!  The 650D has a front USB 3.0 port which will support your USB 3.0 devices.

The Carbide Series cases come with both USB 3.0 and USB 2.0 support.  If your motherboard does not have a USB 3.0 header, then you can use the supplied 3.0 to 2.0 USB adapter which comes with the case. Check out the video below showing you how its done:

Yes!  The Carbide Series cases are designed to accomodate 240mm radiators.

The Carbide Series cases have 8 PCI expansion slots, which will allow the support of 3-way SLI/Crossfire.

The Carbide Series 400R comes with 3x 120mm fans.  There are a total of 10 fan mounting points in the case.  6 of these mounting points will accept either 120mm or 140mm fans, and the remaining 4 will only accept 120mm fans.

The Carbide Series cases have 316mm of space for graphics cards, which should be enough for just about any card!

The fan controller can control up to 4 different fans in your system.  For more information about the configuration and features of the fan controller please check out this blog post.

The 600T has 8 expansion slots and we have test fit our 600T with triple video card configurations without any problems.  You should have plenty of room for this configuration.

This case will fit any graphics card currently on the market, and even if larger cards are released in the future, our HDD cage is removable and can be relocated to the bottom of the case if you require more space.

Alternative side panels and accessories for the 600T can be purchased separately in the case accessories section of our website.

Yes!  The 600T has a front USB 3.0 port which will support your USB 3.0 devices.

The 600T will support ATX and mATX motherboard form factors.

Yes, the hard drive cradles in the 600T are able to secure a 2.5in HDD, SSD or any standard 3.5in drive.

The case is designed to accommodate most a 2x 120mm (240mm) radiator at the top of the case.  In order to use a radiator you will need to remove the 200mm fan at the top of the case.

RPM = 800
CFM Max = 76
dBA Max = 24

The 600T comes with 2x 200mm fans with white LED lights and 1x 120mm fan.

Yes, using the screw holes on the bottom of the cradle (rather than the sides, which are used for standard 3.5in drives) you can secure a 2.5in HDD or SSD.

In most instances you do not need to have the whole case replaced, we can replace the damaged part individually.  Please use Technical Support Xpress to submit a request.

In most systems we would suspect that exhaust fans would make the most sense to be mounted on the top of the case. Every system is going to be slightly different so there is definitely some room to experiment.

Absolutely! Please check the corsair store, here: https://shop.corsair.com/store/item_view.aspx?id=1171683

Newly purchased 800D already support USB 3.0.  If you have an older 800D then you can purchase an upgrade kit by going to the case accessory page on our website.

They will support mATX, ATX, eATX.

The cases are designed to accommodate most 3x 120mm (360mm) radiators with enough space to support push/pull configurations. Measured from edge to edge of the mounting holes on the top of the case there is 10 mm of space between mounting holes.

The rear fan mounting location will support either a 140mm OR 120mm fan.

RPM = 900 +-150
CFM Max = 69
dBA Max = 17.9

The 800D comes with 3x 140mm fans, and the case will support and additional 4x 120mm fans.

The aluminum face plate on the front of the case is removable and it will need to be removed before you have access to remove the drive bay covers.  You will want to hold the top of the case with one hand and then pull outward from the bottom of the face plate.  The aluminum face plate should come right off and once you remove the necessary drive bay covers you can simply line up the face plate and snap it back into place.