
Umstieg auf Kühlmittel
Wenn Sie den standardmäßigen Kühler Ihres Prozessors durch einen Hydro Series H45 ersetzen, wird Ihr Rechner besser gekühlt und läuft geräuschärmer. Die Installation ist einfach: Der H45 wird an der Rückseite des Mainboards Ihres Rechners eingebaut. Sie benötigen lediglich einen Schraubenzieher. Die Installation des Hydro Series H45 gelingt dank der kompakten Komponenten und flexiblen Leitungen selbst dann ohne Probleme, wenn nur wenig Platz zur Verfügung steht. Sie verbessern damit die Prozessorkühlung auch in kompakten Gehäusen. Wenn Ihr Gehäuse eine 120-mm-Lüfterbefestigung in der Nähe des Prozessors aufweist, passt der H45 in der Regel hinein.

Geschlossenes Kühlsystem
Das leistungsfähige System mit Kühlmittel für hochleistungsfähige Prozessoren braucht keine komplexen Leitungsanschlüsse. Der Hydro Series H60 ist ein vorgefülltes geschlossenes System, das niemals neu befüllt werden muss.
Gummileitungen mit geringer Verdampfung
Hohe Lebensdauer dank minimalem Verdampfen des Kühlmittels, robustes Gummi für höchste Flexibilität bei hervorragendem Leckageschutz.

Flache Pumpe
Die Pumpe bietet eine hervorragende Zirkulationsleistung auf kleinstem Raum. Das vereinfacht die Installation und verbessert den Luftstrom im Gehäuse.
Kühlplatte aus Kupfer mit werkseitig aufgetragener Wärmeleitpaste
Dank seiner hohen Thermalleitfähigkeit ermöglicht Kupfer eine effiziente Wärmeabführung an den Verteiler. Weil die Wärmeleitpaste bereits aufgetragen ist, entfällt der Aufwand bei der Installation.
Socket 2011 Hydro Series CPU Cooler Mounting Guide
The new Intel® Socket 2011, used on the new X79 motherboards and the new 2nd generation Intel Core Sandy Bridge-E CPUs, has changed significantly from Socket 1366. As you can see below there are no longer the traditional holes through the PCB. There is now a metal bracket that has been tapped to accept M4 screws. Because of this the Corsair
Hydro Series H70, H80 and H100 CPU coolers all come with separate screws to mount on Socket 2011 boards.
Hydro Series H80 and H100
Included with the H80 and H100 are four standoffs that have a shorter wider end. These are for socket 2011, the shorter end screws into the metal mounting plate on the motherboard.
Install all four of the standoffs as shown below.
After installing and tightening down all four standoffs, the CPU cooler is ready to be installed.
Next the thumb nuts are installed. Tighten these in an X pattern to ensure the pressure is even, resulting in a good mount on the CPU.
Hydro Series H70 Core
The H70 Core uses the same bracket for socket 1155, 1156, 1366, and 2011. Again socket 2011 uses larger M4 screws and does not need the backplate. Make sure all of the holes on the retention ring are towards the outside (as seen below). Then install the M4 screws through these holes.
The retention ring should then be put on the H70 Core. The H70 Core cooling unit and retention ring can then be installed on the motherboard. The M4 screws will screw right into the mounting holes on the motherboard. Again tighten these in an X pattern to ensure the pressure is even resulting in a good mount on the CPU.
Corsair Airflow Pro Installation Guide
We have prepared a short pictorial guide on How To Install the Corsair Airflow Pro Dynamic Memory Display.�
