
Corsair Hydro Series H75 Installation Guide
Veröffentlicht am 10/25/2013VonDustin Sklavos
PC-Gehäuselüfter mit hohem Luftdurchsatz der Corsair Air Series LED kombinieren effizienten, geräuscharmen Luftstrom mit eindrucksvoller LED-Beleuchtung. Die speziell modellierten Blätter sind für die Bereitstellung eines hohen Luftdurchsatzes mit weniger Geräuschen und Turbulenzen als bei herkömmlichen Gehäuselüftern konzipiert. Lichtdurchlässig mit bereifter Struktur, erzeugen sie durch das Licht der vier LEDs einen dramatischen Effekt.
Lüftermodelle der Air Series AF erbringen die beste Leistung in uneingeschränkten Flächen mit mindestens 3 cm Spielraum und eignen sich hervorragend für die Montage an der Rück- oder Oberseite Ihres PC-Gehäuses als Abluftventilatoren für Mainboard und CPU, Grafikbeschleuniger und andere Komponenten, die Ihr Gehäuse erwärmen. Sie arbeiten in Bereichen wie den Seitenwänden oder Lufteinlässen der Unterseite ebenso gut als uneingeschränkte Ansauglüfter.
Sehen Sie sich für stark eingeschränkte Bereiche wie Festplattenkäfige oder andere enge Räume mit weniger Luftvolumen unsere Air Series SP-Modelle für Lüfter mit hohem statischen Druck an.
Lüftermodelle der Air Series AF wurden konzipiert, um Standard-Gehäuselüfter an Leistung zu übertreffen. Die Blätter sind speziell für optimalen Luftstrom modelliert und sind ultra-dünn, um weniger Geräusche und Turbulenzen zu erzeugen. Das ummantelte Lagersystem reduziert Vibrationen und sorgt für einen ruhigen Betrieb.
AF120 Quiet Edition LED | AF140 Quiet Edition LED | |
Abmessungen | 120mm x 25mm | 140mm x 25mm |
Betriebsspannung | 7V - 12V | 7V - 12V |
Leistung bei 12 V | Leistung bei 12 V | |
Luftstrom | 52.19 CFM | 66.4 CFM |
Statischer Druck | .75 mmH20 | .80 mmH20 |
Geräuschpegel | 25.2 dBA | 25.5 dBA |
Geschwindigkeit | 1500 RPM | 1200 RPM |
Energieverbrauch | 0.40 A | 0.23 A |
The new Intel® Socket 2011, used on the new X79 motherboards and the new 2nd generation Intel Core Sandy Bridge-E CPUs, has changed significantly from Socket 1366. As you can see below there are no longer the traditional holes through the PCB. There is now a metal bracket that has been tapped to accept M4 screws. Because of this the Corsair
Hydro Series H70, H80 and H100 CPU coolers all come with separate screws to mount on Socket 2011 boards.
Included with the H80 and H100 are four standoffs that have a shorter wider end. These are for socket 2011, the shorter end screws into the metal mounting plate on the motherboard.
Install all four of the standoffs as shown below.
After installing and tightening down all four standoffs, the CPU cooler is ready to be installed.
Next the thumb nuts are installed. Tighten these in an X pattern to ensure the pressure is even, resulting in a good mount on the CPU.
The H70 Core uses the same bracket for socket 1155, 1156, 1366, and 2011. Again socket 2011 uses larger M4 screws and does not need the backplate. Make sure all of the holes on the retention ring are towards the outside (as seen below). Then install the M4 screws through these holes.
The retention ring should then be put on the H70 Core. The H70 Core cooling unit and retention ring can then be installed on the motherboard. The M4 screws will screw right into the mounting holes on the motherboard. Again tighten these in an X pattern to ensure the pressure is even resulting in a good mount on the CPU.