CORSAIR WARTHOG

The WARTHOG series left Side Glass Panel (A) and right Side Steel Panel (L) are retained by two ball snaps at the top of the case.

• Pull the top of the panel(s) outward and tilt them toward the floor.

The WARTHOG series front panel is fixed to the frame by two hinges, allowing it to swing open like a door. Magnets along its inside edge secure it to the front bezel when closed.

• To open the front panel, pull it outward using the pull tab.

The WARTHOG series Top Panel (G) is secured by two thumbscrews at the rear of the case.

• Loosen the two thumbscrews at the rear of the case.
• Pull the nylon strap backward to remove the Top Panel (G).

The PSU Shroud (E) is held in place by two screws in the rear panel of the case and one screw securing it to the motherboard tray from the right side.

• Remove the three screws.

• Lift the PSU Shroud (E) out of the case.

• Remove the screw at the top of the Side Fan Mounting Bracket (I).
• Tilt the bracket outward to detach it from the case.

For enhanced cable management, the WARTHOG series is compatible with the FRAME 4000D cable shroud (sold separately). It attaches using the same mounting interface as the Side Fan Mounting Bracket (I).

• Align the bottom notches of the cable shroud with the corresponding holes at the bottom of the case.
• Secure the shroud using the top screw.

The RapidRoute 2.0 Motherboard Tray (C) is held in place by four screws along the back of the tray.

• Unscrew these four screws.

• Tilt the tray outward and lift it out.

The WARTHOG series supports mITX, mATX, ATX, and E-ATX motherboards, including ASUS BTF, MSI Project Zero, and GIGABYTE Project Stealth with reversed connections.

• Align the motherboard with the standoffs and secure it with the provided Motherboard Screws (7).

The WARTHOG series includes a RapidRoute 2.0 Motherboard Tray, with additional tray options available (sold separately) to customize your build:

FRAME ELITE Motherboard Tray

• Connect the FPANEL plug to the front panel I/O header on your motherboard, aligning it with the keyed layout. This header is labeled JFP1 on some motherboards.

• Use the included Top-mounted Front I/O Adapter (11) to connect the FPANEL plug to the individual front panel I/O header pins.

The WARTHOG series includes a Reverse Connector Magnetic Strip (1) that is designed to cover the visible edge of the reverse connector holes in the motherboard tray.

• Align the Reverse Connector Magnetic Strip (1) to your standoffs and adjust side to side to close the gap on your motherboard.

If you're installing a motherboard with reverse connectors, the Reverse Connector Magnetic Strip (1) can be used to fill the gap around the 24-pin ATX port, providing a cleaner and more polished appearance.

When installing a standard motherboard, you can slide the Reverse Connector Magnetic Strip (1) behind the board, aligning it with the screw holes along the motherboard tray, to cover the reverse connector slot and conceal any wires running along the motherboard tray for a cleaner look.

CORSAIR InfiniRail™ is an innovative fan and radiator mounting system designed to offer exceptional flexibility and ease of use in PC case builds. Unlike traditional cases with fixed mounting points, InfiniRail utilizes adjustable steel rails that allow users to slide and position fans and radiators precisely where needed.

The WARTHOG series features two of these InfiniRail systems; one on the top and one on the front.

Adjusting the Rails in the Front of the Case

• Loosen the Phillips head screws at both ends of the InfiniRails.
• Adjust both front rails for your fans according to the markings on the case.

Adjusting the Rail on the Top of the Case

• Loosen the Phillips head screws at both ends of the InfiniRail.
• Adjust the the top rail for your fans according to the markings on the case.

Installing 120mm or 140mm Fans

To install 120mm or 140mm fans using the front InfiniRail Fan Mounting System, you need to install the InfiniRail Fan Mounts (2). Use four mounts per fan, two on each side of the rails.

• Clip the InfiniRail Fan Mounts (2) onto the rails by anchoring the inner edge of each mount first, then snapping the outer edge into place.

• Slide the mounts along the rails to align them with your fan mounting points.
• Align your fans to the mounting tabs on the mounts and secure them by screwing in QuikTurn® Fan Screws (3).

• Once aligned, you can lock the setup in place with the InfiniRail Fan Mount Lock Screws (5).

Installing 200mm Fans

200mm fans will screw directly into the InfiniRail mounts without the plastic fan mounts. Remove the mounts if they came pre-installed on your case.

• Align your fans to the mounting slots on the InfiniRails and secure them by screwing QuikTurn® Fan Screws (3) into the fan frame.

• Align your fans to the InfiniRail fan mounting slots and and secure them by screwing QuikTurn® Fan Screws (3) into the fan frame.

To install fans on the side, ensure you have the Side Fan Mounting Bracket (I) installed.

• Align your fans to the fan mounting slots, and and secure them by screwing QuikTurn® Fan Screws (3) into the fan frame.

• Align your fans to the fan mounting holes on the PSU Shroud.
• Secure the fans with Long Fan Screws (6).

• Align your fan to the fan mounting holes.
• Secure the fan with Long Fan Screws (6).

• Align your fan to the fan mounting holes.
• Secure the fan by screwing in QuikTurn® Fan Screws (3).

The WARTHOG series has fill / drain ports pre-punched in the top and bottom panels for a Hydro X open loop liquid cooling setup.

• Remove the port covers by gently prying them off with a flathead screwdriver.

The WARTHOG series offers several locations to mount a radiator for liquid cooling, with the front and top locations featuring an adjustable InfiniRail fan mount. Please refer to the Fan Installation section for details on using the InfiniRail Fan Mounting System.

Top mounting provides optimal noise performance, but other mounts can be utilized based on your build preferences. Consult your cooler's product manual for more tips on usage and best practices.

The WARTHOG series cases includes one Combination Drive Plate, capable of mounting one HDD and two SSDs simultaneously.

• Unscrew the thumbscrew securing the Combination Drive Plate (H), then remove the plate.

• Install the SSD(s) onto the Combination Drive Plate (H) by securing it to the bottom of the plate using the included SSD Screws (8).

• Install the HDD onto the Combination Drive Plate (H) by securing it to the bottom of the plate using the included HDD Screws (7).

The Combination Drive Plate (H) also serves as a mounting location for an iCUE LINK System Hub controller, if one is used. The System Hub features magnets to keep it secure but if it's moving around due to cable tension, double-sided adhesive pads can also be used.

Reinsert the Combination Drive Plate (H) into its designated slot in the case, then secure it by tightening the thumbscrew clockwise.

• Install the PSU with the fan facing down.
• Secure the power supply to the chassis with the two captive screws located on the back of the case.
• For additional security, secure the PSU using two Motherboard Screws (7) screws in the corners of the rear panel.

CORSAIR SHIFT power supplies have side-mounted connections for easy access for building and upgrades. The WARTHOG series was designed with SHIFT in mind, providing sufficient clearance for cable bending and routing.

• SHIFT power supplies install identically to a standard ATX PSU.

The included PCI bracket allows the WARTHOG series to support both horizontal and vertical GPU mounting configurations.

• Unscrew the PCIe slot covers and remove them.

• Insert the card into the PCIe slot until it clicks into place with the PCIe slot's retention mechanism.
• Align the bracket with the PCIe slots and secure the card to the case.

The Nano GPU Anti-sag Stabilization Arm supports your graphics card, preventing it from bending or sagging under the weight of its heatsink. This not only helps protect your graphics card and PCIe slot, but also contributes to a cleaner, more professional-looking build.

• Adjust the Nano GPU Anti-sag Stabilization Arm (D) by loosening the front-facing thumbscrew and sliding it up or down.

The WARTHOG series supports vertical GPU mounting with the included PCI Plate (B) and a PCIe Riser Card (sold separately).

• Uninstall the PCI Plate (B) by loosening the two screws at the rear of the case.

• Rotate the PCI Plate (B) 90 degrees counterclockwise so that the PCIe slot cover thumbscrews face upward.

• Re-attach the PCI Plate (B) and secure the thumbscrews.

• Install the Vertical Mount Standoffs (10) from the accessory box to the top of the PSU shroud. There are two locations for standoffs, so choose the location that best suits the size of your GPU in relation to how far it is from the side panel.

• Mount the PCIe Riser Card (sold separately) to the standoffs using the screws that came with the Riser Card.

• Mount the GPU into the PCI bracket by firmly seating it into the riser card until it clicks, then secure it with thumbscrews.

Please visit the CORSAIR RS Series Quick Start Guide for instructions on fan installation.

The WARTHOG series features three removable dust filters and one additional filter in the accessory kit box.

• Open the front panel door to access the Front Fan Filter (J).
• To remove the filter, tilt it away from the front of the case using the pull tab at the top.

• To remove the magnetic Side Panel Filter (H), pull at the sides to detach it from the Side Panel (L).

• To remove the Bottom Filter (F), grip the edge of the filter frame and slide it outwards.

The WARTHOG series features the RapidRoute 2.0 cable management system, identified by the distinctive squircle patterns throughout the case. Wherever you see these squircles, you’ve found a pegboard-compatible mounting point.

Your case comes with five pre-installed RapidRoute 2.0 Ratcheting Strap Mounts With Straps (13). Each strap is designed to securely cinch cables against the mount's plastic base. You can reposition these mounts in any orientation to suit your cable management needs.

Removing a RapidRoute Mount

• Pull the plastic plunger located at the center of the RapidRoute 2.0 Ratcheting Strap Mount.

• Pull the mount off the squircle, tilting it off in the direction of the retaining hook.

• Position the RapidRoute 2.0 Ratcheting Strap Mount where you would like it and repeat the previous steps in reverse to re-position the clip. Install the hook & loop strap on one side of the clip.
• Run your cables through the channel, then route the strap over the cables and through the opposite side of the strap mount to secure them against the mount and motherboard tray.

The WARTHOG series includes various cable management features such as:

• Multiple positions for RapidRoute 2.0 ratcheting straps to accommodate standard or reverse connector motherboards.
• Zip tie points are strategically placed for routing power cables to specific devices.
• iCUE LINK cable hooks in the top panel to securely hold LINK cables without permanent attachment.
• Supports most reverse connector motherboards (MSI, ASUS, GIGABYTE) that feature connectors on the rear of the board for a build with no visible motherboard cables.
• A dedicated location for your iCUE LINK System Hub.
• Two cable routing holes allow front panel I/O cables to enter the case. The forward position prioritizes external visibility, while the rear position routes the cable into the PSU shroud for a cleaner internal appearance.

CORSAIR WARTHOG series cases come with a 2-year warranty.

©2026 CORSAIR MEMORY, Inc. All rights reserved. CORSAIR and the sails logo are registered trademarks of CORSAIR in the United States and/or other countries. All other trademarks are the property of their respective owners. Product may vary slightly from those pictured.