
How to install the Hydro Series H100i CPU Cooler
Pubblicata su 02/22/2013Da Jeff Checchi
Hydro Series™ H50 consente di migliorare con facilità il raffreddamento delle CPU Intel. Questo sistema di raffreddamento a liquido indipendente è efficiente e più silenzioso delle ventole per CPU standard. Inoltre, grazie al design compatto, è ideale per i case di piccole dimensioni.
Sostituendo il dissipatore di calore standard della CPU con un Hydro Series H50 si otterrà un maggiore livello di raffreddamento e di silenziosità per il tuo PC.
Se si ha accesso al retro della scheda madre del PC è possibile installare H50 senza problemi. Tutto ciò che occorre è un giravite.
Le dimensioni compatte dei componenti e i tubi flessibili consentono la facile installazione di Hydro Series H50 anche in presenza di spazio ridotto. È possibile aumentare l'efficienza di raffreddamento della CPU anche nelle situazioni di minor spazio; H50, infatti, può essere montato quasi dappertutto, a condizione che il case disponga di un punto di montaggio per ventola da 120 mm vicino alla
Hydro Series H50 è preriempito e non necessita di ulteriore riempimento, né di manutenzione.
Il design modulare semplifica l'installazione ed è compatibile con tutti i moderni processori Intel.
La velocità ridotta e il diametro elevato assicurano livelli di rumorosità più bassi rispetto alle ventole più veloci e di minori dimensioni utilizzate nei sistemi di raffreddamento standard delle CPU. Il connettore a tre pin è compatibile con i controller della ventola.
L'evaporazione ridotta del liquido refrigerante prolunga la durata del sistema, mentre la gomma resistente garantisce flessibilità elevata e un'ottima protezione contro le fuoriuscite.
L'unità di pompaggio assicura un'elevata velocità di circolazione pur occupando poco spazio. In questo modo l'installazione è semplificata e il flusso d'aria all'interno del case circola più liberamente.
Il rame è un ottimo termoconduttore, mentre il design delle alette è concepito per uno scambio di calore ottimale.
Il design sottile consente di ridurre il flusso d'aria necessario, con conseguente aumento della silenziosità. Le dimensioni ridotte facilitano l'installazione e migliorano la compatibilità. Infine, il rivestimento nero offre un incredibile impatto visivo.
![]() | CW-8960012 Hydro Series H40/H50/H55/H70/H90/H110 AMD Mounting Bracket Kit | |
![]() | CW-8960013 Hydro Series H40/H50/H55/H70/H90/H110 Intel Mounting Bracket Kit |
The new Intel® Socket 2011, used on the new X79 motherboards and the new 2nd generation Intel Core Sandy Bridge-E CPUs, has changed significantly from Socket 1366. As you can see below there are no longer the traditional holes through the PCB. There is now a metal bracket that has been tapped to accept M4 screws. Because of this the Corsair
Hydro Series H70, H80 and H100 CPU coolers all come with separate screws to mount on Socket 2011 boards.
Included with the H80 and H100 are four standoffs that have a shorter wider end. These are for socket 2011, the shorter end screws into the metal mounting plate on the motherboard.
Install all four of the standoffs as shown below.
After installing and tightening down all four standoffs, the CPU cooler is ready to be installed.
Next the thumb nuts are installed. Tighten these in an X pattern to ensure the pressure is even, resulting in a good mount on the CPU.
The H70 Core uses the same bracket for socket 1155, 1156, 1366, and 2011. Again socket 2011 uses larger M4 screws and does not need the backplate. Make sure all of the holes on the retention ring are towards the outside (as seen below). Then install the M4 screws through these holes.
The retention ring should then be put on the H70 Core. The H70 Core cooling unit and retention ring can then be installed on the motherboard. The M4 screws will screw right into the mounting holes on the motherboard. Again tighten these in an X pattern to ensure the pressure is even resulting in a good mount on the CPU.