Hydro Series™ H110i は、280mmラジエーターマウントを搭載するケース用で、エクストリームパフォーマンスを発揮するオールインワンCPUクーラーです。CORSAIR iCUE 互換
sku: CW-9060026-WW
Hydro Series H110i は、280mmラジエーターマウントを搭載するケース用で、エクストリームパフォーマンスを発揮するオールインワンCPUクーラーです。280mmラジエーターとデュアルSP140L PWMファンでハイパフォーマンスCPUに必要とされる優れた熱分散を提供します。CORSAIR iCUEにも対応し、システム温度のモニター、クーリングパフォーマンスの調整、LEDライティングのカスタマイズが直接デスクトップ上から変更できます。
素早く効率的な冷却の秘訣は、冷却表面を最大化することです。お手持ちのPCケースが280mmラジエーター用にデュアル140mmファンマントを搭載しているのであれば、H110iで最大の冷却性を活かすことができます。
カスタムデザインの140mmファンは、高い静圧を実現するようにカスタム設計され、乱気流とノイズを最小限に抑えます。PWM制御のためファンスピードを最適なパフォーマンス・ノイズの割合にカスタマイズできます。
マザーボード上のUSBヘッダーに同梱のCORSAIR iCUEケーブルを接続し、無料のCORSAIR iCUEソフトウェアをダウンロードします。これによりさらなるパワーを発揮できます。冷却パフォーマンスのカスタマイズ、クーラントとCPU温度のモニタリング、RGB LEDライティングを初期設定のホワイトからシステムに応じた色に変更したり、温度変化やその他の入力に応じで色が変更するように設定することが可能です。
H100iは、クーロズドループ設計でクーラントも予め補充されています。モジューラーのツールレスマウンティングブラケットが同梱され、素早い取り付けが可能です。高い効率性を誇る進化したコールドプレートとポンプ設計になっています。
Corsair Hydroシリーズ水冷CPUクーラーは、コンパクトで取り付けやすいパッケージで水冷の魅力を提供します。高いオーバークロッキングパフォーマンスに対応する優れた冷却性を典型的な複雑な水冷キットを利用せずに実現します。
CORSAIR iCUE ソフトウェアは、RGB ライティングのダイナミック同期、速度をカスタマイズ可能なサイレンスファン、高度なシステムモニタリングにより、システムを活性化します。
詳細を見る
The new Intel® Socket 2011, used on the new X79 motherboards and the new 2nd generation Intel Core Sandy Bridge-E CPUs, has changed significantly from Socket 1366. As you can see below there are no longer the traditional holes through the PCB. There is now a metal bracket that has been tapped to accept M4 screws. Because of this the Corsair
Hydro Series H70, H80 and H100 CPU coolers all come with separate screws to mount on Socket 2011 boards.
Included with the H80 and H100 are four standoffs that have a shorter wider end. These are for socket 2011, the shorter end screws into the metal mounting plate on the motherboard. Install all four of the standoffs as shown below. After installing and tightening down all four standoffs, the CPU cooler is ready to be installed. Next the thumb nuts are installed. Tighten these in an X pattern to ensure the pressure is even, resulting in a good mount on the CPU.
The H70 Core uses the same bracket for socket 1155, 1156, 1366, and 2011. Again socket 2011 uses larger M4 screws and does not need the backplate. Make sure all of the holes on the retention ring are towards the outside (as seen below). Then install the M4 screws through these holes. The retention ring should then be put on the H70 Core. The H70 Core cooling unit and retention ring can then be installed on the motherboard. The M4 screws will screw right into the mounting holes on the motherboard. Again tighten these in an X pattern to ensure the pressure is even resulting in a good mount on the CPU.