
Installing a Corsair Hydro Series Cooler on Ryzen with the AM4 Bracket
Publicado em 04/26/2017Por Joseph Ocbina
O Hydro série H55 é a atualização de refrigeração fácil para CPUs Intel. O sistema de refrigeração líquida eficiente e autossuficiente é mais silencioso e mais eficiente do que ventiladores de CPU comuns, e o design compacto o torna ideal para gabinetes menores.
O PC operará mais frio e silencioso quando o dissipador de calor padrão da CPU for substituído por um Hydro série H55.
Instalação direta: se é possível alcançar a parte de trás da placa mãe do PC, é possível instalar o H55. Tudo o que você precisa é de uma chave de fenda.
Os componentes compactos e a tubulação flexível tornam o Hydro série H55 fácil de instalar, mesmo em espaços apertados. Ele permite melhorar a eficiência de refrigeração da CPU, mesmo nos gabinetes mais compactos — desde que o gabinete tenha uma montagem de ventilador de 120mm perto da CPU, o H55
O Hydro série H55 vem pré-preenchido e nunca precisa ser cheio ou preparado novamente.
O design modular simplifica a instalação e é compatível com processadores Intel e AMD.
A baixa velocidade e o grande diâmetro reduzem os níveis de ruído em relação aos ventiladores menores e mais rápidos usando e refrigeradores de CPU comuns. O conector de três pinos é compatível com controladores de ventilador.
A evaporação mínima do refrigerante ajuda a assegurar a longa durabilidade; e a borracha resiliente oferece alta flexibilidade e excelente proteção contra vazamentos.
A unidade da bomba fornece circulação de alta velocidade sem ocupar muito espaço. Isso facilita a instalação e ajuda a melhorar o fluxo de ar no gabinete.
O cobre tem excelentes características térmicas e o design das hastes é otimizado para troca de calor eficiente.
O baixo perfil reduz os requisitos de fluxo de ar, o que ajuda o H55 a ser mais silencioso. O pequeno tamanho também possibilita uma instalação mais fácil e uma maior compatibilidade, além de o acabamento preto ter uma ótima aparência.
![]() | CW-8960012 Hydro Series H40/H50/H55/H70/H90/H110 AMD Mounting Bracket Kit | |
![]() | CW-8960013 Hydro Series H40/H50/H55/H70/H90/H110 Intel Mounting Bracket Kit |
The new Intel® Socket 2011, used on the new X79 motherboards and the new 2nd generation Intel Core Sandy Bridge-E CPUs, has changed significantly from Socket 1366. As you can see below there are no longer the traditional holes through the PCB. There is now a metal bracket that has been tapped to accept M4 screws. Because of this the Corsair
Hydro Series H70, H80 and H100 CPU coolers all come with separate screws to mount on Socket 2011 boards.
Included with the H80 and H100 are four standoffs that have a shorter wider end. These are for socket 2011, the shorter end screws into the metal mounting plate on the motherboard.
Install all four of the standoffs as shown below.
After installing and tightening down all four standoffs, the CPU cooler is ready to be installed.
Next the thumb nuts are installed. Tighten these in an X pattern to ensure the pressure is even, resulting in a good mount on the CPU.
The H70 Core uses the same bracket for socket 1155, 1156, 1366, and 2011. Again socket 2011 uses larger M4 screws and does not need the backplate. Make sure all of the holes on the retention ring are towards the outside (as seen below). Then install the M4 screws through these holes.
The retention ring should then be put on the H70 Core. The H70 Core cooling unit and retention ring can then be installed on the motherboard. The M4 screws will screw right into the mounting holes on the motherboard. Again tighten these in an X pattern to ensure the pressure is even resulting in a good mount on the CPU.
“H55 is priced around £50, making it affordable to go down the ALC route without having to burn a hole in your pocket. At this price-point H55 offers a great alternative to air cooling.” “Corsair continue to impress even at the lower-end within the Hydro Series. H55 is affordable, good quality and offers a convenient alternative to bulky air cooling.”
Revisão completa!