
How to install the Hydro Series H100i CPU Cooler
Publicado em 02/22/2013Por Jeff Checchi
O design da segunda geração do Hydro série H60 oferece refrigeração de CPU potente e eficiente. O ventilador reprojetado e o radiador de baixo perfil ajudam o H60 a remover rapidamente o calor da CPU quando ela está sendo usada intensamente.
Atualize o seu ventilador de CPU comum ou seu volumoso refrigerador de ar para a eficiência e simplicidade da refrigeração líquida de CPU. Aproveite um melhor desempenho em refrigeração e menos ruídos e proteja o seu investimento em CPU.
Os ventiladores de 120mm incorporam pás de projeto personalizado para melhor pressão estática para relação de ruído, oferecendo maior desempenho a níveis de ruído mais baixos.
Vigorosa refrigeração líquida para CPUs de alto desempenho não significam mais ter que lidar com bombeamentos complexos. O Hydro série H60 vem pré-preenchido e nunca precisa ser cheio ou preparado novamente.
O design modular simplifica a instalação e é compatível com processadores Intel® e AMD®.
A evaporação mínima do refrigerante ajuda a assegurar a longa durabilidade e o design flexível proporciona uma maior proteção contra vazamentos e facilita a instalação em pequenos espaços.
O cobre tem uma melhor condutividade térmica para melhor transferência de calor para o tubo de distribuição. O composto térmico pré-aplicado permite economizar uma etapa de instalação possivelmente complicada.
![]() | CW-8960004 Hydro Series H60/H80/H100 AMD Bracket Kit | |
![]() | CW-8960005 Hydro Series Fan Cable Extension Kit, 2x 12" 4 pin extender cables, H60 H80 H100 |
The new Intel® Socket 2011, used on the new X79 motherboards and the new 2nd generation Intel Core Sandy Bridge-E CPUs, has changed significantly from Socket 1366. As you can see below there are no longer the traditional holes through the PCB. There is now a metal bracket that has been tapped to accept M4 screws. Because of this the Corsair
Hydro Series H70, H80 and H100 CPU coolers all come with separate screws to mount on Socket 2011 boards.
Included with the H80 and H100 are four standoffs that have a shorter wider end. These are for socket 2011, the shorter end screws into the metal mounting plate on the motherboard.
Install all four of the standoffs as shown below.
After installing and tightening down all four standoffs, the CPU cooler is ready to be installed.
Next the thumb nuts are installed. Tighten these in an X pattern to ensure the pressure is even, resulting in a good mount on the CPU.
The H70 Core uses the same bracket for socket 1155, 1156, 1366, and 2011. Again socket 2011 uses larger M4 screws and does not need the backplate. Make sure all of the holes on the retention ring are towards the outside (as seen below). Then install the M4 screws through these holes.
The retention ring should then be put on the H70 Core. The H70 Core cooling unit and retention ring can then be installed on the motherboard. The M4 screws will screw right into the mounting holes on the motherboard. Again tighten these in an X pattern to ensure the pressure is even resulting in a good mount on the CPU.
“What we are saying though is that if you have got £60 to spend on cooling, you're up for a bit of overclocking fun, you fancy a bit of a dip into water cooling and you like your case to look open clean and sexy, then you owe it to yourself to have a bit of a gander at the Corsair H60.”
Revisão completa!The H60 “2.0” was everything we were hoping for from a refreshed Corsair product and then some. Everything from its noise levels to overall performance has been improved by leaps and bounds. Granted, the intergenerational performance jump isn’t extreme, but for $80 we’d be hard pressed to ignore it. "Much of the H60’s newfound strength comes from the custom Corsair SP120 running at its heart. Due to a high static pressure envelope this fan is able to push large amounts of air through the radiator without making an ungodly amount of noise. Coupled with larger tubing, an updated pump and a slightly revised radiator design, the SP120 brings Corsair’s H60 to the next level."
Revisão completa!“The kit is very easy to install, 10 minutes tops really, and after connecting the two wires for powering up the fan and pump you are good to go. So there you have it you guys. I definitely like what the updated H60 has to offer, and that is very decent cooling performance and downright great looks for any PC. Definitely recommended.”
Revisão completa!“The Corsair H60 is an excellent choice for anyone who wants to enter the liquid cooling world, as it is easy to install and fits virtually any case.”
Revisão completa!