SABRE v3 PRO PureVector ULTRALIGHT ERGO

Connect the USB CHARGING / DATA CABLE (J) to an available USB 2.0 or 3.X port on your PC and to the USB CHARGING / DATA PORT (G) on the mouse. The MULTI-PURPOSE INDICATOR LED (F) will indicate charging status (see Mouse Status and Indications).

The USB CHARGING / DATA CABLE (J) connects either the USB WIRELESS RECEIVER (I) or the mouse - not both at the same time.

• Connect the USB CHARGING / DATA CABLE (J) to an available USB 2.0 or 3.X port on your PC, then plug the other end into the USB WIRELESS RECEIVER (I).
• Place the receiver near your mouse for the best wireless performance.
• Power on your mouse by switching the POWER / WIRELESS MODE SWITCH (H) to 2.4GHz.
• When successfully connected, the MULTI-PURPOSE INDICATOR LED (F) shows solid green for 2 seconds and then turns off.

To use the mouse in wired mode, disconnect the USB CHARGING / DATA CABLE (J) from the USB WIRELESS RECEIVER (I) and plug it into the USB CHARGING / DATA PORT (G) on the mouse. The mouse switches to wired mode automatically and charges at the same time.

There is no dedicated DPI button on this mouse.

• Press and hold the RIGHT MOUSE BUTTON (B) and the BACK BUTTON (E) together for 3 seconds to cycle through DPI stages.
• The MULTI-PURPOSE INDICATOR LED (F) flashes the corresponding color 3 times, then turns off.

*Advanced configurations are available via CORSAIR WEB HUB.

Step 1 – Connect Your Mouse
A. Connect the USB CHARGING / DATA CABLE to your PC and to the USB WIRELESS RECEIVER.
B. Make sure the power switch is set to 2.4GHz.
To use the mouse in wired mode instead, move the cable from the receiver to the mouse. The mouse switches to wired mode automatically and charges at the same time.


Step 2 – Open CORSAIR WEB HUB and Select the Mouse
A. Go to https://www.corsair.com/web-hub/index.html.
B. Click [Add Device].
C. In the HID device dialog, choose:
- CORSAIR SABRE v3 PRO WIRELESS USB Receiver (wireless mode), or
- CORSAIR SABRE v3 PRO PureVector ULTRALIGHT ERGO Gaming Mouse (wired mode).
D. Click [Connect].

Step 3 – Set DPI Levels

A. Click [DPI] in the left sidebar.

B. The mouse ships with 5 DPI stages: 400 / 800 / 1200 (default) / 1600 / 2000.

C. Use the slider or type a value to adjust each stage, and use the toggle to enable or disable individual stages.

D. Click [Reset to Default] to restore the factory DPI stages.

E. Optional: Use PureVector calibration by Aimlabs to optimize your DPI performance. Click [Open AimLabs] or get it on Steam. After calibration, all other DPI stages will be disabled.

*For the full PureVector calibration walkthrough, see STEP-BY-STEP PUREVECTOR GUIDE.

*Sniper (DPI Shift button) is only available if assigned to a button.

Recommended starting DPI:

- Desktop/general: 1200–1600 DPI

- FPS games: 800–1200 DPI

- MOBA/MMO: 1600–2000 DPI

Step 4 – Remap Buttons (Assignments)

A. Click [Assignments] in the left sidebar.

B. Click the button on the virtual mouse you want to change. Five buttons are programmable: Left Click, Right Click, Middle Click, Forward, Back. The power/wireless switch is not programmable.

C. Choose the Assignment Type from the left list:

• Keyboard Keys (Basic Keys / Functional Keys / System Keys)
• Mouse Buttons.
• Media and Volume
• Macro (record multiple keystrokes)
• Text

D. You can also drag a key from the list directly onto the virtual mouse.

E. Confirm the assignment and test it. Click [Reset to Default] to restore the original layout.

Step 5 – Device setting

A. Click Device Setting at bottom left.

B. Adjust the following:

• a. Battery – Shows wireless connectivity and battery status.

• b. USB Wired Polling Rate – 125 Hz / 250 Hz / 500 Hz / 1,000 Hz (default) / 2,000 Hz / 4,000 Hz / 8,000 Hz.

• c. SLIPSTREAM WIRELESS Polling Rate – 125 Hz / 250 Hz / 500 Hz / 1,000 Hz (default) / 2,000 Hz / 4,000 Hz / 8,000 Hz. Higher polling rates improve response time but use additional system processing power. Changing the polling rate may briefly disconnect your device.

• d. Brightness – Adjust the brightness of the MULTI-PURPOSE INDICATOR LED.

• e. Sleep Time – Switches the device to a low-power state after a set period of inactivity. Default 3 min, adjustable 1–40 min.

• f. Angle Snapping – Enables smoother mouse movement for drawing straight lines

• g. Lift Height – Allows you to adjust vertical height at which the mouse sensor stops sending a signal to your computer when you lift the mouse.

• h. Surface Selection – Optimize performance for your surface: Default / MM Glass / MM PRO / MM / MM350 PRO / MM200.

• i. Motion Sync – Makes cursor movements feel smoother and more accurate by keeping them in sync with your system. On / Off.

• j. Ripple Control – Reduces tiny unwanted cursor jitters, especially at high DPI. On / Off.

• k. Reset to Factory Settings – Restore all device settings to default values.

• l. Click [Save] to apply your changes.

Step 6 – Update firmware

A. Connect one device to your PC:

– Mouse: connect the mouse to your PC with the USB CHARGING / DATA CABLE.

– Receiver: connect the USB WIRELESS RECEIVER to your PC with the USB CHARGING / DATA CABLE.

B. Go to CORSAIR WEB HUB, click [Add Device], and select the connected device - CORSAIR SABRE v3 PRO PureVector ULTRALIGHT ERGO Gaming Mouse or CORSAIR SABRE v3 PRO WIRELESS USB Receiver.

C. Click Device Settings at the bottom left to open the DEVICE SETTINGS panel.

D. At the top of the panel, next to Firmware, click [Check for Updates].

E. If the latest firmware is already installed, the page displays "The latest firmware version is installed." Otherwise, follow the on-screen instructions to complete the update.

F. Disconnect the device, then repeat steps A–E for the other one.

*Do not unplug the device or close the browser during the update process.

Manual firmware update (optional)

Use this only if you need to install a specific firmware file provided by CORSAIR Support.

A. In the CORSAIR FIRMWARE UPDATE UTILITY, click the three-dot menu at the top right of the device card and select [Manual Update].

B. The MANUAL FIRMWARE UPDATE window shows the current firmware version of the device.

C. Drag and drop the firmware file into the window, or click the upload area to select the file (zip).

D. Click [Update] and wait for the update to complete.

Step 7 – Pair wireless receiver

Manual re-pairing is only available through the CORSAIR FIRMWARE UPDATE UTILITY.

A. Connect the USB WIRELESS RECEIVER to your PC with the USB CHARGING / DATA CABLE (J) and switch the mouse on (2.4GHz).

B. Go to the CORSAIR FIRMWARE UPDATE UTILITY. (In CORSAIR WEBHUB you can also reach it from Device Settings → Pair Wireless Receiver → [Go].)

C. Click [Add Device] and authorize CORSAIR SABRE v3 PRO WIRELESS USB Receiver.

D. On the receiver card, click the three-dot menu at the top right and select [Pair].

E. On the mouse, press and hold the LEFT MOUSE BUTTON (A), RIGHT MOUSE BUTTON (B) and MIDDLE CLICK / SCROLL WHEEL (C) together for 2 seconds. The MULTI-PURPOSE INDICATOR LED (F) blinks yellow for about 20 seconds.

F. Move the mouse close to the receiver. The LED shows solid yellow for 2 seconds and then turns off - pairing is complete.

PureVector calibration by Aimlabs analyzes your aim and applies calibrated directional sensitivity to your mouse. The calibration is applied per DPI stage and is saved to the onboard memory of the mouse, so your profile travels with you - no background app required.

*Requires Aimlabs on Steam and a free Aimlabs account. Make sure the mouse and the wireless receiver are both running the latest firmware (see Step 6 of the STEP-BY-STEP MOUSE SETUP GUIDE).

Step 1 – Open PureVector in CORSAIR WEB HUB

A. Connect your mouse, open CORSAIR WEB HUB, and click [DPI] in the left sidebar.

B. Select the DPI stage you want to calibrate.

C. In the PureVector panel, click [Open AimLabs] to launch Aimlabs through Steam. If Aimlabs is not installed, click [Get it on Steam] to download it.

*After calibration, all other DPI stages will be disabled.

Step 2 – Sign in to Aimlabs

A. Launch Aimlabs.

B. Sign in, or create an Aimlabs account. An account is required to access PureVector features.

Step 3 – Open Mouselabs in Aimlabs

After you sign in, click [Go now] if you are prompted to open the PureVector page. You can also select Mouselabs in the top menu.

Step 4 – Run calibration

A. Click [Start calibrating].

B. Answer the setup questions, then click [Continue].

C. Select your grip style, then click [Continue].

D. Select your aim style, then click [Continue].

E. Select your mousepad size, then click [Continue].

F. Search for your mouse model and set your DPI (in-game sensitivity auto-filled from Aimlabs), then click [Start calibrating].

G. Click to begin. Calibration consists of 5 rounds of Spidershot tasks, 1 minute per round (about 5 minutes in total).

H. After the 5th round, click [Done] to save the calibration data to your mouse.

Step 5 – Review your results

A. Return to the Mouselabs panel. It now shows additional data, including the PureVector card on the left. Your setup is saved automatically.

B. Select the PureVector tab on the right to view the Before and After PureVector graphs.

C. All 5 calibration rounds are recorded. Click any round to watch its replay.

*The After PureVector graph appears only after you complete at least 5 more rounds of any Aimlabs task following your first calibration. Play more rounds to keep adding data to it.

Step 6 – Refine or reset your calibration

A. To run calibration again, click [Refine calibration].

B. To remove the calibration data from your mouse, click the Reset button.

BATTERY REMOVAL DIAGRAM NEEDED

This product uses a rechargeable battery and safety guidelines must be followed in the event that the product is disabled for disposal and recycling. To safely remove the battery for disposal and recycling, follow the numbered steps with the below diagrams.

CORSAIR MEMORY, Inc. encourages customers to recycle used electronic hardware and rechargeable batteries in accordance with local laws and regulations.

The power delivered by the charger must be between min 1.25 Watts required by the radio equipment, and max 2.5 Watts in order to achieve the maximum charging speed.

• BATTERY INFORMATION
• M/N(型號): TW 302535
• Rating: 3.7V, 210mAh, 0.777Wh
• Scan QR code for battery detail information

© 2026 CORSAIR MEMORY, Inc. All rights reserved. CORSAIR and the sails logo are registered trademarks of CORSAIR in the United States and/or other countries. All other trademarks are the property of their respective owners. Product may vary slightly from those pictured.

FCC ID: 2AAFM-RGP0193 (Mouse)

FCC ID: 2AAFM-RGP0195 (Dongle)

IC: 10954A-RGP0193 (Mouse)

IC: 10954A-RGP0195 (Dongle)