
Installing a Corsair Hydro Series Cooler on Ryzen with the AM4 Bracket
发布于 04/26/2017发布人Joseph Ocbina
保护硬件并提高您 CPU 的超频潜能。双风扇和双倍厚度散热器提供了出色的冷却效率。
无需其他硬件 - 只需将随附的 Corsair Link 电缆连接到主板上的 USB 管脚,然后下载免费的 Corsair Link Dashboard 软件。您可以直接在桌面监控冷却液温度并调整冷却性能。
120mm 风扇采用定制设计的叶片,能够以较低的噪音提供静压空气,以更低的噪音水平显著提高性能。
Hydro 系列 H80i 已预先注满液体,永远不需要补充冷却液或加水。
模块化设计简化了安装,并且与 Intel® 和 AMD® 处理器兼容。
最少冷却液蒸发有助于确保长使用寿命,而且弹性材料可实现高灵活性和卓越的防泄漏性能。
The new Intel® Socket 2011, used on the new X79 motherboards and the new 2nd generation Intel Core Sandy Bridge-E CPUs, has changed significantly from Socket 1366. As you can see below there are no longer the traditional holes through the PCB. There is now a metal bracket that has been tapped to accept M4 screws. Because of this the Corsair
Hydro Series H70, H80 and H100 CPU coolers all come with separate screws to mount on Socket 2011 boards.
Included with the H80 and H100 are four standoffs that have a shorter wider end. These are for socket 2011, the shorter end screws into the metal mounting plate on the motherboard.
Install all four of the standoffs as shown below.
After installing and tightening down all four standoffs, the CPU cooler is ready to be installed.
Next the thumb nuts are installed. Tighten these in an X pattern to ensure the pressure is even, resulting in a good mount on the CPU.
The H70 Core uses the same bracket for socket 1155, 1156, 1366, and 2011. Again socket 2011 uses larger M4 screws and does not need the backplate. Make sure all of the holes on the retention ring are towards the outside (as seen below). Then install the M4 screws through these holes.
The retention ring should then be put on the H70 Core. The H70 Core cooling unit and retention ring can then be installed on the motherboard. The M4 screws will screw right into the mounting holes on the motherboard. Again tighten these in an X pattern to ensure the pressure is even resulting in a good mount on the CPU.
"There’s very little to dislike about the H80i. It's even easier to install and better built than the H80 before it, and produces consistently improved cooling results than the older model too. Better yet, it only costs an extra £5, putting it on par with Antec's Kuhler H20 920 (which it also trumps) and thus representing very good value too. Our concerns about it being used as an intake were nullified by its excellent performance as an exhaust setup, even in our minimal airflow test chassis."
完整评论�Overall we are very impressed by what the Corsair H80i has to offer. It improves significantly on the previous H80 model which was already one of the best coolers on the market.�
完整评论“CORSAIR has reset the bar again at a higher level. Outperforming their own range, adding the LINK software and this complete performance bundle operates at a lower noise level. The 120mm H80i will blend in perfectly in most enclosures, while the 240mm H100i needs a dual 120mm top case. The installation is pure child’s play and no worrying about DIMM incompatibility with your cooling setup. Without any surprise the cooling performance of both Hydro units is again top notch. Being covered by a 5 year warranty, how can you go wrong with one of these new Hydro Coolers?”
完整评论"Corsair Hydro H80i is a really nice end water cooling package. The model adds a number of improvements over its predecessor, including an improved water block and more lavish fans. Moreover, the model has support from the board for Corsair Link superb control software that completely blows away competing solutions." (Google Translation)
完整评论