
SKU CW-9060021-WW
Hydro Series™ H100i GTX 超高性能液冷 CPU 冷却器
Hydro Series™ H100i GTX 液冷 CPU 冷却器具有一个 240mm 散热器和双 SP120L PWM 风扇,能够提供超频 CPU 所需的卓越的散热性能。
与CORSAIR iCUE兼容
Hydro Series™ H100i GTX 液冷 CPU 冷却器具有一个 240mm 散热器和双 SP120L PWM 风扇,能够提供超频 CPU 所需的卓越的散热性能。
与CORSAIR iCUE兼容
Hydro Series H100i GTX 是一款超高性能一体式液冷 CPU 冷却器,适用于具有 240mm 散热器安装位置的机箱。240mm 散热器和双 SP120L PWM 风扇能够提供超频 CPU 所需的卓越的散热性能。内置 CORSAIR iCUE,让您可以直接从桌面监控温度、调整冷却性能和定制 LED 照明效果。
双宽度散热器利用 120mm 或 140mm 散热器,为我们的 Hydro Series 冷却器提供近两倍的冷却面积。几乎适用于 240mm 散热器提供双 120mm 风扇安装位置的所有机箱。
我们的 SP120L 风扇采用不同于标准机箱风扇的定制设计 – 它们经过定制设计,可提供较高的静压以便直接安装在散热器中,并且风扇叶片的形状经过特殊设计,可在噪音最小的情况下实现最大送风量。由于该风扇由 PWM 控制,您可以定制风扇速度,选择性能/噪声曲线上的最佳点。
将内置 CORSAIR iCUE 电缆连接到主板 USB 端板,并下载免费 CORSAIR iCUE 软件,以解锁更多功能。您可以定制冷却性能,监控冷却剂和 CPU 温度,将 RGB LED 照明颜色从默认白色更改为匹配您的系统,或者基于温度读数和其他输入更改颜色。
工作量繁重的水冷操作已经一去不复返了。H100i GTX 是一种闭环设计,已预装冷却剂,它包含一个模块化免工具安装支架,可更快安装。
Corsair Hydro Series CPU 冷却器让您能够在一个紧凑的、易于安装的封装中进行液冷。可为超频性能提供出色的冷却效果,无需复杂的传统水冷套件。
The new Intel® Socket 2011, used on the new X79 motherboards and the new 2nd generation Intel Core Sandy Bridge-E CPUs, has changed significantly from Socket 1366. As you can see below there are no longer the traditional holes through the PCB. There is now a metal bracket that has been tapped to accept M4 screws. Because of this the Corsair
Hydro Series H70, H80 and H100 CPU coolers all come with separate screws to mount on Socket 2011 boards.
Included with the H80 and H100 are four standoffs that have a shorter wider end. These are for socket 2011, the shorter end screws into the metal mounting plate on the motherboard.
Install all four of the standoffs as shown below.
After installing and tightening down all four standoffs, the CPU cooler is ready to be installed.
Next the thumb nuts are installed. Tighten these in an X pattern to ensure the pressure is even, resulting in a good mount on the CPU.
The H70 Core uses the same bracket for socket 1155, 1156, 1366, and 2011. Again socket 2011 uses larger M4 screws and does not need the backplate. Make sure all of the holes on the retention ring are towards the outside (as seen below). Then install the M4 screws through these holes.
The retention ring should then be put on the H70 Core. The H70 Core cooling unit and retention ring can then be installed on the motherboard. The M4 screws will screw right into the mounting holes on the motherboard. Again tighten these in an X pattern to ensure the pressure is even resulting in a good mount on the CPU.